Edelbrock 70405 Installationshandbuch

Thank You….…for purchasing an Edelbrock Nitrous Oxide Injection System.Nitrous Oxide injection is one of the most exciting performance enhancements, f

2.4 Nitrous Feed Line Mounting1. Determine the route your main nitrous feed line will follow. Ensure the path does not route the nitrous feed linetoo

Here is a typical EFI solenoid assembly, mounted in the enginecompartment of a vehicle, using an unmodified EFI solenoidbracket. Modifications perform

3.1 Nitrous Electrical Components Bill of Materials (BOM)Nomenclature Descriptions:ATO… the fuse configuration is ATO. When replacing this fuse, ask f

3.2 Nitrous Electrical System Wiring Diagram

3.3 Nitrous Electrical System Installation ProceduresDetermine the location of the relay and fuse holder wire harness. Most common installations locat

3.5 Arming Switch and InstallationThe arming switch is a red, lighted switch that is a “MASTER” arming switch for your nitrous system. Without it,your

3.6 Microswitch Installation and Wiring (continuation)...The bolts used to attach the microswitch have extra length to allow for spacing the microswit

4.0 Voltage Booster Unit Installation and Wiring4.1 Voltage Booster Relays Bill of MaterialsNomenclature Descriptions:ATO...the fuse configuration is

RelayRelaySocketSocketGround To ChassisPositive Output FromVoltage Booster UnitPink / Brown+ Fuel PumpWireBlue To + From VBUGreen From Fuel Pump +Red

4.3 Voltage Booster Unit Installation ProceduresDetermine the mounting location of your Voltage Booster Unit in the engine compartment of your vehicle

Caution!!Before You Install Your Edelbrock Nitrous System…Please read this Installation manual fully before installing this system.You will need to ha

4.5 Voltage Booster Unit Relay InstallationThe Voltage Booster Unit Relays need to be mounted in the trunk of the vehicle within range of the fuel pum

4.6 Testing Voltage Booster Before RunningFollow the following steps to ensure that the Voltage Booster Unit is properly installed on you vehicle. Fai

6.0 Solenoid Inspection and Maintenance1. Close valve on nitrous bottle.2. Make sure all nitrous supply lines are free of pressure before removal of a

7.0 Troubleshooting Your Edelbrock Nitrous SystemHow to use our Troubleshooting Flowchart:The troubleshooting of a nitrous system is basic and straigh

Symptom #5… No change in performance when system is activated.1. System wired incorrectly.a. Compare wiring to schematic.i. Wire per instructions.2. L

Symptom #6… Engine detonates mildly when system is activated.1. Inadequate octane fuel.a. Verify what gasoline you use.i. Use higher-octane fuel.2. Sp

WHAT IS NITROUS OXIDE?Nitrous Oxide is a cryogenic gas composed of nitrogen and oxygen molecules. It is stored as a “gas over a liquid” which means th

1.0 Introduction to your Edelbrock 4.6L Mustang Performer EFI Nitrous SystemWithin the pages of this manual is information, safety tips and operation

1.2 Jet Map InformationEdelbrock Engineering has conducted dyno testing with the Edelbrock 4.6L Mustang Performer EFI system to ensurethe horsepower i

1.4 Performer Kit Bill of MaterialsQty. DescriptionNozzle and Nozzle Hardware1 ea. Nitrous fan spray nozzle1 ea. Nitrous fan spray nozzle bulkhead bod

2.0 Nitrous System Installation2.1 Nitrous Bottle InstallationThe nitrous oxide storage cylinder is typically called a “nitrous bottle”. It is an alum

2.2 Bottle OrientationAccurate calibration of your nitrous system depends on the bottle remaining at a stable temperature. Choosing theproper location

2.3 Nitrous Bottle InstallationAfter you have determined the location and orientation of the nitrous bottle, use the following procedure to installthe