Edelbrock 1403-1413 Bedienungshandbuch

Stöbern Sie online oder laden Sie Bedienungshandbuch nach Kfz-Zubehör & Komponenten Edelbrock 1403-1413 herunter. Edelbrock 1403-1413 Owner`s manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 4
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 0
Brochure #63-0061
© 2002 Edelbrock Corporation
Page 1 of 4
Rev. 01/02
EDELBROCK PERFORMER SERIES CARBURETORS
CATALOG #1403 #1404, #1405, #1406, #1407, #1409,
#1410, #1411, #1412 & #1413
INSTALLATION INSTRUCTIONS
PLEASE study these instructions and the "Important Information Regarding Edelbrock Performer Series Carburetors" completely and thoroughly
before installing your new carburetor. If you have any questions or problems, contact our Technical Hotline at: 1-800-416-8628, 7 am - 5 pm
Monday-Friday, Pacific Standard Time or e-mail us at edelbr[email protected]. Please fill out and return the EPS carburetor Warranty Card.
DESCRIPTION: The Edelbrock Performer Series carburetor has been calibrated, factory flow-tested, and preset. Please read all instructions prior to
installation. For "Theory of Operation" and "Tuning Procedures", see the accompanying carburetor Owner's Manual.
Edelbrock Performer Series carburetors are not for computer-controlled applications. That includes some 1981 & later GM vehicles
with Q-Jet carburetor and some 1981 & later Ford vehicles with automatic overdrive (AOD) transmissions.
1 - Installation instruction sheet
1 - Owner’s Manual
1 - Warranty card
1 - Carburetor accessories brochure
1 - Square-bore base gasket
1 - Air horn gasket
1 - Air cleaner stud
1 - Vacuum “T” (except #1409 &1410)
1 - 1/4" pipe plug
2 - Vacuum caps
1 - Throttle cable ball end stud (except
#1409 & 1410)
1 - Red choke positive wire (1403, 1406,
1409, 1410, 1411 & 1413 only)
1 - Black choke ground wire (1403, 1406,
1409, 1410, 1411 & 1413 only)
4 - Carburetor studs/nuts/washers
(1406,1409,1410,1411 & 1413 only)
1 - #8018 Transmission kick-down stud
for 1406, 1411 & 1413 only
1 - Vacuum hose (1406, 1411 & 1413
only)
1 - #8009 Throttle cable stud for 1406,
1411 & 1413
INSTALLATION KIT CONTENTS
Replace fuel filter. Dirt found in carburetor voids warranty.
Check and replace the air filter if necessary.
Check PCV valve and replace if clogged.
Check all hoses for leaks or cracks and replace if necessary.
Check fuel pump for proper operation and replace if necessary.
Check the intake manifold and cylinder head gaskets for leaks and
replace if necessary.
Check the ignition system: clean and gap or replace spark plugs,
plug wires, and adjust ignition timing.
Check The Following Items Befor
e Carburetor Installation
PostScript Picture
(Edelbrock B/W Logo.eps)
Parts:
New fuel filter (Edelbrock #8135 or equivalent).
Chrome Steel Fuel Line Kit #8134 includes fuel filter.
Banjo Fuel Fitting #8089 (if required for fuel line clearance using
your air cleaner).
New air cleaner (Edelbrock #1221 or #4221). If stock or other air
cleaner is to be used, check fit on carburetor before installation to
determine if air cleaner spacer (Edelbrock #8092; 3/4" tall) is
required.
Choke cable kit (manual choke carburetor) or electrical connectors
(electric choke carburetor).
Carburetor adapter, if carburetor is to be installed on other than
square-bore intake manifold. See Steps #4 and #5 following for
specific part numbers. Do not use a 4-bbl. to 2-bbl. adapter;
Edelbrock carbs must be used on intake manifolds designed for 4-
bbl. carburetor only!
Throttle Linkage Kits for Ford or Chrysler applications
(see Carburetor PREPARATION, Step #1).
Throttle, trans. and cruise control bracket #8036 or #8030 (chrome)
for 1972-78 small-block Chevrolet. Other applications may require
modification to original throttle cable bracket.
Universal throttle return spring kit #8005 if original return spring can
not be used.
Divided square-bore heat insulator gasket #9266 for dual-plane
(stock or Performer-type) manifolds. May be used in place of square-
bore adapter plate #2732 on some Edelbrock manifolds.
Tools:
Sockets/wrenches/tubing wrenches
Pliers
Screwdrivers
Hacksaw and/or tubing cutter
Torx Driver (for electric choke models)
Wire crimpers (for electric choke models)
Test Meter or Test Light (for electric choke models)
Additional Parts and Tools Required for Installation
Seitenansicht 0
1 2 3 4

Inhaltsverzeichnis

Seite 1 - INSTALLATION INSTRUCTIONS

Brochure #63-0061© 2002 Edelbrock CorporationPage 1 of 4Rev. 01/02EDELBROCK PERFORMER SERIES CARBURETORSCATALOG #1403 #1404, #1405, #1406, #1407, #140

Seite 2 - Fuel Filter

Brochure #63-0061© 2002 Edelbrock CorporationPage 2 of 4Rev. 01/02FUEL INLET for 3/8" hose (exceptmarine models #1409 & #1410which use a 3/8&

Seite 3 - Lever #1483

Brochure #63-0061© 2002 Edelbrock CorporationPage 3 of 4Rev. 01/025. You must use an EdelbrockAdapter #2732 when installing aPerformer Series Carb onE

Seite 4 - Manual choke cable and fuel

Brochure #63-0061© 2002 Edelbrock CorporationPage 4 of 4Rev. 01/02CARBURETOR INSTALLATION1. Remove rag from intake manifold and install new studs, mou

Kommentare zu diesen Handbüchern

Keine Kommentare